2001 Yamaha YZF 600 R thunder cat replace the triple trees


Yes, I have a 2001 Yamaha yzf600R and when putting my triple tree on I noticed my left shock sits high than my right one. With the shock coming out more on the top how to do get the shock to lower down one shock higher than the other side want this affect the ride is why I was wondering how to get the shock compressed back down since the left shock is higher than the right one and looks odd with the triple tree on. @

Obat Herbal Kanker Kelenjar Getah Bening Alami Stadium 4

Front wheel bearings. We have a 2004 Limited and ended up getting both replaced (at different times) paid for by Ford. We only had 40,000 km on the vehicle at the time and had to fight Ford to cover the cost. The did come through in the end.

Turns out that after 26 years and 233 thousand miles, the original strut gave up the ghost: Rust! I took the shock strut assembly out of a 'spare parts' Honda Accord I keep and replaced the broken one in the Honda I am now driving. Mechanically the car is still excellent, but the car is destined to dissolve around me! To remove the whole assembly required taking out one 14mm bolt at the bottom and three 12mm bolts at the top, some WD 40, several pieces of wood for leverage and a heavy mallet.. Since there is a heavy duty coil spring involved, one should take out the bottom bolt first and lift the bottom of the strut free from its position, ( this is where I used a long 2x4 and another piece of wood as the fulcrum point to pry the strut upward) Then undo the top 3 bolts and the whole unit falls out. You will also need to detach the brake fluid line that uses the strut itself as an anchor. The easiest way is to take the line off from the back of the brake drum housing ( 9mm nut) and remove the horseshoe clip and push the curved metal brake line through the small hole where the line is anchored to the strut. Use care as you will need to reattach the brake line again after installing the next shock strut. (Coil spring compression tool required) Needless to say, you will need to jack the car up and remove the rear tire first to access the whole thing.

On this model vehicle the rear shockers should have air bags to keep car at normal ride height, when load changes.
The air bag can sometimes become caught between inner and outer tubes of shocker when car is raised and lowered quickly.
You will need to jack car up from tow hitch or frame to lower rear axle, this will unfold air bag, slowly lower car, with ignition on, this will make sure air compressor is filling air bags as they take the load.
Hope this is helpful, MMP

It is for any thing you may wont to add like extra lighting or 12volt power. They are usually just wired with a hot wire in and a plug or post for you to add a 12v line to assory

OMG! men i got exactly the same problem and tought i could repair it myself so i took the bike apart (thinking that a fuel line was craked or something) but when i look everything seemed fine so i did more research and it was coming out from the carburator so i took it to the dealer and got it fixed for about 600$ and everything if perfect now (mine is also a 2002 one)

Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Yamaha YZF600 YZF600R Thundercat 1994 2007 Service Manual Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-yamaha
YAMAHA YZF600R Owner Manual
Yamaha YZF 600 Thunder cat
Yamaha YZF600R Wikipedia


More: